Just How to Replace a Bath Tub
Just How to Replace a Bath Tub
Blog Article
What're your ideas concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a new one is additionally a reasonably difficult task. If the old tub is readily easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also place the new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you install a new tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water system pipes.
Your devices as well as material checklist need to consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the supply of water as well as check all joints and new pipework for leakages and also tighten them if essential. Load the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at least once as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in location in between the tap and also the sink. Secure the tap in place with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and fittings. They are sold in tubes and cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our piece on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking time to read our post. If you appreciated our blog post please be sure to share it. I am grateful for your time. Come back soon.
Click For More Information Report this page